I have now left it with the batteries out in the hope that a day or two without batteries will discharge whatever is remembering the connectivity - trouble is for all I know the connection status could be stored in the transceivers rather than in the keyboard. I have tried everything I can think of to logically disconnect this keyboard, but to no avail. Whilst trouble shooting the problem I managed to also connect the keyboard to the third transceiver, so now every character comes out once on my laptop and twice on the desktop ((LLIIKKEE TTHHIISS)). This keyboard was being received on two different transceivers at the same time. This morning it took me a while to realise that the strange behaviour on my laptop was caused by someone typing on the desktop keyboard. Until today this keyboard logically connected to one of the two C-B033 transceivers. The desktop PC also has a wireless keyboard, marked Logitech Deluxe 660 cordless desktop. The other two are both C-B033 transceivers connected to one of the desktop PCs, so that we can have two different rechargeable Logitech RAK89D mice and swap them over when the batteries get low.One is a C-BT44 connected to my laptop docking station and is just used for a Logitech RX 650 mouse.Start > Programs > Logitech > Mouse and Keyboard > Mouse and Keyboard Settings. To customize touchpad settings: Launch the Logitech SetPoint mouse and keyboard software. See answer 360023357073 for instructions. Click the Help button for definitions to these options.I have three different Logitech wireless transceivers. NOTE: If you dont already have SetPoint installed, you can download it. Use the checkboxes to disable the options given. Open SetPoint and click the My Keyboard tab at the top of the window and select the Keyboard Inactive Key Settings tab on the left side (shown below). Open SetPoint and click the My Keyboard tab at the top of the window and select the Keyboard Connection tab on the left side (shown below).Ĭlick the Secure button to secure the keyboard if you do not see the "Your keyboard is secured" message shown in the screenshot above. This is recommended when you use your MX 3000 in an environment with other 27 MHz wireless devices within approximatly a 6 foot (2 meter) range. You can secure your cordless desktop to protect your privacy. Click Help to find detailed descriptions of these options. Use the drop down menus and sliders to find the iNav settings that are right for you. NOTE: If you do not have SetPoint installed, you can download it from the K350 Downloads Page. Open SetPoint and click the My Keyboard tab on the top of the screen and select the Keyboard iNav Settings tab on the left (shown below). Launch SetPoint (Start > Programs > Logitech > Mouse and Keyboard > Mouse and Keyboard Settings). To disable keys you dont use: Launch SetPoint (Start > Programs > Logitech > Mouse and Keyboard > Mouse and Keyboard Settings). Once SetPoint opens, click the My Mouse tab on the top of the. If you do not have SetPoint installed you can download it on our MX 5000 Downloads Page. Open SetPoint (Start > Programs > Logitech > Mouse and Keyboard > Mouse and Keyboard Settings). The iNav wheel is located on the left side of the keyboard (shown below). Changing the function of a button to perform a specific task. Select the key you wish to customize under the Select F Key field.Ĭhange Side-to-side scrolling speed and adjust the scrolling size for the iNav wheel. Open SetPoint and click the My Keyboard tab on the top of the screen and select the Keyboard F Key Settings tab on the left (shown below). The F Mode LED on the receiver will be off in Enhanced F Keys Mode. NOTE: To use the programmed F-Key, make sure to toggle on Enhanced F Keys Mode by pressing the F Mode key. Similar to the Programmable Keys (discussed above), the F-Keys can also be programmed to perform certain functions. The Function Keys, or F-Keys, are the keys labelled F1 through F12 above the number keys. You can also click Help to find detailed descriptions of these options for your device.Ĭlick Apply to save your settings. Now select the task you want the keyboard key to perform under Select Task. Select the key you wish to customize under the Select Hot Key field. You will see the MX 3000 Keyboard listed on the Select Keyboard drop-down (shown below). Once SetPoint opens, click the My Keyboard tab on the top of the screen. If you do not have SetPoint installed you can download it on our MX 3000 Downloads Page. This tutorial will show you how to use the following features in Logitech's Mouse and Keyboard Software (SetPoint):Ĭhange key assignments, set up a desktop search tool, assign keystrokes to one key, and more.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |